Lennox Heat Pump Installation Nationwide | Dalton Heating & Air Long Beach

Lennox Heat Pump Installation in Long Beach: What to Know First

Heat pump installation for a Lennox system in Long Beach typically runs $3,500 – $7,500 depending on the model line, your home’s ductwork, and whether you’re replacing an existing air handler or starting fresh. We install Lennox heat pumps as an independent Lennox service provider, which means we’re not tied to a manufacturer’s sales quota, and we stock parts for the Lennox lines we see most in Long Beach: the Merit series, Elite series, and Signature series. If you’re weighing repair against replacement, or if your Lennox system is short-cycling, icing up, or struggling to hold temperature in Long Beach’s salty, humid air, call (562) 512-7423 for a free estimate. This page is for homeowners who already own a Lennox product and want a straight answer about what installation actually involves, what it costs, and who’s showing up. That last part matters. Around here, that’s us, and we put the price in writing before any work starts.

Call (562) 512-7423

How Lennox Products Fail – and How We Fix Them

Lennox builds solid equipment, but every brand has weak points. Here’s what we see on Lennox heat pump installation calls across Long Beach, from Bluff Park Craftsman homes to the 1950s ranches in Los Altos and the newer builds near El Dorado Park.

• Merit series (ML14XP1, ML16XP1) – reversing valve sticking. The reversing valve is the part that flips your heat pump between cooling and heating. On Merit-series units exposed to Long Beach’s salt air, especially within a few miles of the coast, the valve body corrodes faster than the compressor does. The symptom is a unit that cools fine but won’t heat, or heats fine but won’t cool. We replace the valve and the solenoid coil together, not just one half, because swapping one side of a corroded valve is a call-back waiting to happen.
• Elite series (XP20, XP25) – variable-speed board communication faults. Elite-series Lennox heat pumps use a communicating thermostat and a main control board that talk to each other constantly. When the board loses communication, the unit will lock out and show an error code the owner can’t do anything with. Sometimes a power flicker causes it. Long Beach’s marine layer means the outdoor unit’s low-voltage connections see more moisture than inland units. We clean and reseal those connections, verify the board’s firmware, and only replace the board if it’s actually failed. Half the time it’s a corroded connector, not a board.
• Signature series (SL25XPV) – defrost sensor failures. Signature-series units run a smart defrost cycle, but the defrost temperature sensor sits near the bottom of the outdoor coil where salt spray and dirt accumulate. When that sensor reads wrong, the unit will either defrost too often or not enough. You’ll see a frosted coil in mild Long Beach weather. We replace the sensor with an OEM part and clean the coil. This is a ten-dollar part and a two-hour job, not a refrigerant problem.
• All Lennox heat pump lines – condensate drain clogs in our humidity. Long Beach’s combination of ocean humidity and mild winters means heat pumps run in heating mode at night and cooling mode by afternoon. That cycling creates condensate in both the indoor air handler and the outdoor unit’s base pan. When drains clog, water backs up into the blower cabinet or puddles under the outdoor unit. We clear the full drain line, not just the visible section, and replace the p-trap if it’s cracked.
• Legacy Lennox units (XP13, XP14, older R-410A systems) – coil leaks at the header joints. We still see plenty of 10 – 15 year old Lennox heat pumps in East Long Beach and near the Traffic Circle. The indoor coil header joints are where leaks start on these units. The system loses refrigerant slowly, which means it runs longer, which means higher SCE bills. We’ll pressure-test with nitrogen, find the exact leak location, and give you a written price for either brazing the joint or replacing the coil. If the unit’s over 12 years old and the leak’s in the coil, we’ll be straight with you about whether replacement makes more sense than repair.

Marco Benitez grew up in East Los Angeles and learned his trade at Los Angeles Trade-Technical College before spending close to two decades turning wrenches on residential and light-commercial systems across Southern California. He and the crew have been running service calls in Long Beach for years, including a stretch of older Craftsman homes near Bluff Park where outdated ductwork and aging condenser units keep the schedule full. He reads a system the way a mechanic reads an engine: methodically, without guessing, and with a written price on the table before any work starts.

Our Lennox Heat Pump Installation Process

Every Lennox heat pump installation in Long Beach follows the same sequence. No shortcuts, no surprises. Here’s what happens when you call us.

1. 1
   You call, a person answers. Live phone support, 24/7. You’ll describe what your Lennox system is doing, or whether you’re planning a replacement. We’ll schedule a time and give you a window. We arrive inside that window or we call ahead.
2. 2
   We assess the whole system. Not just the heat pump, but the air handler, the ductwork, the electrical service, the thermostat wiring, and the slab or pad the unit sits on. A Lennox heat pump installation is only as good as the ductwork it breathes through. We measure static pressure and check duct sizing before quoting anything.
3. 3
   You get a written price. Not a verbal range, not a number on a napkin. A line-item written price for the equipment, the labor, the electrical work, the refrigerant, the permit, and the disposal of the old unit. That price doesn’t change unless we find something structural we could not have seen during the assessment, and even then we stop and tell you first.
4. 4
   We install by the book. Braze lines with nitrogen flowing to prevent oxidation inside the piping. Pull a deep vacuum to at least 500 microns and hold it to prove the lines are sealed. Properly flare connections on any ductless-style Lennox equipment. We set the outdoor unit on a level pad, not directly on dirt, because Long Beach’s sandy soil settles.
5. 5
   We test and dial in charge. We charge the system by superheat and subcooling measurements, not by a guess or a rule of thumb. Then we run the unit through heating and cooling cycles and measure the temperature split. If the numbers aren’t right, we don’t leave.
6. 6
   We clean up, walk you through it, and put the guarantee in writing. The site is left clean. We show you the filter, the thermostat, the drain, and the labels. Then we hand you the written guarantee, and explain the 365-Day Done Right Promise: if it’s not done right, we make it right.

What Lennox Heat Pump Installation Costs in Long Beach

Straight numbers, since that’s probably why you’re here. In Long Beach, a Lennox heat pump installation typically runs:

• Entry-level Merit series heat pump, existing ductwork: $3,500 – $4,800. This is a single-stage unit with a 14 – 16 SEER2 rating, installed on a standard existing air handler or furnace with a cased coil.
• Mid-range Elite series heat pump: $4,800 – $6,200. Two-stage or variable-speed equipment, 17 – 20 SEER2, usually paired with an upgraded thermostat and better filtration.
• High-end Signature series heat pump: $6,200 – $7,500 or more. Variable-speed, top efficiency, and often requires a communicating thermostat and surge protection. In Long Beach’s mild climate, the efficiency pays back slower than in Palm Springs, so we’ll be honest about whether this tier makes sense for your house.

What moves the price: whether we’re reusing existing ductwork or sealing and modifying it, how far the electrical panel is from the outdoor unit, whether the old unit used R-22 or R-410A, and what kind of pad or stand the unit will sit on. The estimate is free, and it’s in writing. Call (562) 512-7423 and we’ll come out, look at your specific house, and give you a fixed number.

Why Long Beach Homeowners Call Dalton Heating & Air Long Beach for Lennox Work

Plenty of companies can sell you a heat pump. The reason homeowners in Long Beach call us for Lennox work is simpler than a sales pitch: we show up when we say we will, the price is in writing before any work starts, and we stand behind the job for a full year. The 365-Day Done Right Promise means if the installation isn’t done right, we come back and make it right, no argument and no invoice. That’s a full year of coverage, not a 30-day window. We’re a Garrison Partners company, operating under The Garrison Standard since 2003, and every job is bound to The Garrison Code: arrive inside the stated window, price in writing before starting, do the job by the book, leave the site clean, and stand behind the work for a full year. Our techs are background-checked and uniformed, so you know who’s coming before they arrive. And while Lennox is the focus here, we’re factory-trained to service nine major residential HVAC brands: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. If your house has a mixed system, we can handle it in one visit instead of telling you to call someone else.

FAQs